Seiko I Infotech LP-1030 User's Guide Page 165
- Page / 290
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8-3
▼Setting items
Chapter 8 "FUNCTION" menu
MENU PRINT
Prints the system version, device configuration information, parameter
setting information and status of consumables, etc.
<Parameter (choice execution method)> : Default value
SYSTEM Prints the System menu information (initial value).
PORTn Prints the setting information for the Ethernet port.
Note 1)
PARA Prints the setting information for the Parallel channel.
Note 2)
USB Prints the setting information for the USB channel.
Note 2)
ALL Prints All of the above setting information.
Note 1) Disabled ports will not be indicated.
Note 2) Parallel and USB will only be indicated when
each interface is installed.
Downloaded From ManualsPrinter.com Manuals
- LP-1020L 1
- CE Marking 4
- Seiko Instruments Europe S.A 4
- European Head Office 4
- Introduction 5
- Safety Precautions 6
- Warning labels 9
- How to read this manual 11
- 1 Press to proceed to the 13
- 2 Press and select “SETUP.” 13
- 3 Press or and select 13
- Supplied components 14
- TABLE OF CONTENTS 15
- Chapter 3 Menu overview 3-1 17
- Chapter 13 Terioplot 13-1 22
- Appendix Appendix-1 23
- Getting started 25
- Features 26
- Operating conditions 28
- Installation space 30
- Supported 31
- Spool memory configuration 34
- Right side/rear side 36
- Interior 37
- Control panel 38
- Data standby display 40
- Data processing display 40
- Printing in progress display 41
- Print information display 41
- Setting ready display 41
- Error display 41
- Warming up display 42
- Power saving display 42
- Basic operations 43
- Plotting procedures overview 44
- Turning the power on and off 45
- Power on 46
- Installation operations 49
- Proceed to the next page 50
- Online and offline 52
- Replacing paper rolls 53
- Press the key 54
- Press the 54
- How to detach the paper rolls 56
- 2 Move the flange guide 58
- 5 Cut the end of the paper 59
- Close the paper roll drawer 60
- Replacing the toner 61
- Precautions on handling 62
- 1 Open the toner cover 63
- Return the lever to the left 65
- New bottle 68
- Bottle containing 68
- 6 Close the waste door 69
- 4 Remove the orange tape 73
- 7 Close the top cover 74
- 8 Remove the filter cover 74
- 9 Replace the filter 75
- 1 Adjust the paper guide 76
- 1 Set the paper feeding mode 77
- 2 Load the cut paper 77
- Example of A3 width cut paper 80
- Manual paper feed inlet 80
- Cut paper 80
- Print stop 81
- Continue printing 81
- Cancel printing 82
- Additional printing 82
- Web function 83
- 2 Launch the Web browser 84
- Cleaning the exterior 85
- Limiting rolls to be used 90
- Menu overview 91
- Channels and ports 92
- Data formats 93
- Reprinting 94
- Settings menu 95
- Menu name 96
- (Refer to “Note” below.) 97
- PDL menu 98
- Items which you can set 99
- Printing status 100
- Menu screen 101
- Device menu “DEVICE” 102
- Paper menu “PAPER” 103
- Function menu “FUNCTION” 104
- Protocol menu “PROTOCOL” 105
- Reset menu “RESET” 106
- System menu “SYSTEM” 107
- Basic Menu Operation 109
- Offline menu operation 111
- Moving the menu hierarchy 112
- Exiting the setting 118
- "SETUP" Menu 119
- Setting parameter items 120
- ▼Setting parameter items 121
- Setup parameter priority mode 128
- PARAMETER MODE (DSCAN only) 129
- AUTO SUPPLY 130
- FIXING MODE 131
- COPY COUNT 132
- SUPPLY PARAM 133
- DRAWING PARAM 135
- Error memo 138
- Paper feed 138
- Cut position 138
- SCALING PARAM 139
- ROUND BUTT 149
- MITERED length 150
- RASTER PARAM 152
- "DEVICE" menu 153
- Setting items 154
- POWER SAVE 155
- EDGE CUT TIMER 156
- DOOR OPEN CUT 157
- TRACING PAP. MODE 157
- BOTTLE MAINT 158
- "PAPER" menu 159
- MEDIA SERIES 161
- "FUNCTION" menu 163
- MENU PRINT 165
- (Sample of print) 166
- HPGL SELF PLOT 167
- Note 2) 168
- ERROR LOG 169
- ENGINE LOG 172
- SYSTEM DATE 173
- SYSTEM TIME 173
- INIT CHARG. INF 173
- PRINT CHARG. INF 173
- MAINTE INFO 174
- DATA DUMP 174
- "PROTOCOL" menu 175
- PDL SELECT 177
- XPT PORT 178
- PRINTER NAME 178
- USER NAME 179
- "RESET" menu 181
- Reset functions 182
- PORT RESET 183
- "SYSTEM" menu 185
- WEB LOCK 189
- ENABLE SERIES 190
- APPLY ROLL 192
- CHINA SIZE 194
- INITIAL SET 195
- LANGUAGE 196
- LENGTH UNITS 196
- ADMIN PASSWORD 196
- 1 Press the key 197
- 2 Press the or key 197
- 3 Press the key 197
- Chapter 12 199
- ▼Setting items 201
- PORT SELECT 202
- IP ADDRESS 203
- SUBNET MASK 203
- ROUTING TABLE 204
- SETUP DETAILS 205
- Terioplot 211
- Settings 214
- Restrictions 215
- Troubleshooting 217
- When an error message appears 219
- 1 Open the top cover 220
- 2 Remove the jammed paper 220
- 4 Remove the jammed paper 221
- 1 Open the cutter door 223
- 2 Open the cutter door 224
- Open the cutter door inside 225
- Open the cutter door (⇒Step 1 227
- 4 Cut the end of the paper 228
- Door Open 230
- ■Roll 1 drawer (Door 1) 230
- ■Roll 2 drawer (Door 2) 230
- ■Manual feed drawer (Door 4) 230
- ■Cutter door (Door 5) 230
- ■Top cover (Door 6) 231
- ■Fixation door (Door 7) 231
- Operator Call 232
- ■Operator notice warning 233
- ■Communication warnings 236
- ■PDL warning 237
- Chapter 14 Troubleshooting 239
- ■Engine warning 240
- ■Main warning 240
- Service Call Errors 241
- ■Serial number not set 241
- ■Engine error 241
- ■System error 241
- ■Controller errors 242
- Error log 245
- Log Registration Format 246
- Type of Error Log 247
- Warning (Classification: W) 248
- ▼Troubleshooting for ethernet 251
- ■If "MANUAL" is set 252
- ■If "AUTO" is set 252
- Appendix 255
- Plotter Specification 256
- Appendix-3 257
- ▼ Basic specifications 257
- Menu structure 258
- Appendix-5 259
- ▼ Menu structure 259
- Appendix-6 260
- Appendix-7 261
- Appendix-8 262
- Appendix-9 263
- [DEVICE] MENU 264
- [PAPER] MENU 265
- [FUNCTION] MENU 266
- [PROTOCOL] MENU 267
- #SYSTEM RESET 268
- #PORT RESET 268
- >PORT1 268
- [SYSTEM] MENU 269
- Appendix-16 270
- Appendix-17 271
- H H' 272
- Appendix-19 273
- Appendix-20 274
- Command list 275
- Appendix-23 277
- ▼ Command list 277
- Appendix-24 278
- HP RTL Plotting Command List 279
- Appendix-26 280
- D-SCAN Format Command List 281
- Appendix-28 282
- Appendix-29 283
- Appendix-30 284
- Appendix-31 285
- Appendix-32 286
- TIFF Tag 287
- CALS Format Records 288
- Appendix-35 289
- Appendix-36 290
- ■ lpd support commands 290
Related products and manuals for Print & Scan Seiko I Infotech LP-1030
(241 pages)© 2020, manymanuals.com. All rights reserved. | 0.328 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals